Ask me anything about vehicle repair | Page 4 | Squat the Planet

Ask me anything about vehicle repair

fimbulvetr

Active member
Joined
Nov 17, 2018
Messages
31
Reaction score
17
Location
Yakima, WA
Howdy! Good question!

First, you'll want to have a way to change out a tire, and have a spare tire for when you need it. You can get a T-handle wrench with 4 different sizes in 1 tool, or since you only need 1 Size for your lug nuts, save weight and get a breaker bar and socket. You'll need a jack to raise vehicle too, but your van should have one of those. If not, get a small scissor jack or bottle jack. I usually carry a piece of 2x4 also, to give myself a "foot print" for if I need to jack up vehicle in sand or gravel or dirt. Being prepared to change your own flat tire is going to save you at least $150 tow bill. A tire plug kit is good item to have in a pinch also.

Next would be jumper cables. A jump pack is ideal, but they are big and costly, not needed. Small jump packs are becoming available, but they are pricey. Nice to have though. Even if you have a jump pack, you'll want cables for when the pack is dead and you didn't know it was dead. I personally also carry around an 80w solar panel to recharge a dead battery.

As far as tools go, I carry full set of wrenches, standard and metric. Not needed for 1 vehicle, but I find myself working on other cars besides my own on the road. A set of 3/8" drive sockets and ratchet will be handy. Get the 6 point kind vs. 12 point. I find the 12 point sockets strip slightly rusty bolt head too easily.
Some brake calipers require Torx or hex drive bits to removed and install new pads.

Other basic hand tools I don't travel without are pliers (2 or 3 styles) a hammer, pry bar, big pair of channel lock pliers also, for pushing caliper pistons back in when installing new brake pads. A few different size screw drivers are good to have.

Solid Metal wire is a good temp fix item to have on board, as well as electrical tape and some wire nuts. Have a couple extra fuses of assorted sizes, make sure you know what fuses your van takes before buying some. There are 3-4 main styles.

*This is all pretty general stuff to have, I encourage everyone to become familiar with their vehicle to know exactly what tools to have to preform basic fixes on the road.

Everyone is different in their ability to repair shit on the road, and the more you feel confident in doing, the more tools you'll want to have.

*Your specific van (99 gmc) does not run a timing belt, so no worries there. I would however do a transmission fluid drain and fill. Do not flush. Can remove the pan and change filter too if you want, good idea. Other areas of common failure are chassis parts; tie rod ends, ball joints, etc. These things can be difficult to change on side of road, but possible. Starters, alternators, batteries, drive belts, brakes, even water pumps can all be fixed on side of road. These are things you'll want tools for. Also, like most of us, we tend to put alot of stuff/weight inside vans, well because they hold alot! New shocks on all 4 Conners are a night and day difference when driving. If you've loaded the van up good, I recommend new shocks.

Hope this helped! Good luck and safe travels!


Thank you for the expansive response. I do need to get I jack actually. My van was a Comcast service van in it's previous van and it had a server rack, which I had to sawzall out piece by piece because it was welded in, but to that end it also had two 90AH deep cycle batteries, which are connected to the alternator, with what looks like a buck converter. I have since bolted two 100 watt solar panels(I got from a guy that was liquidating his solar installation company) to the roof and a charge controller and now the battery bank can charge off either the solar panels, or the alternator, which is nice and I got cables that can reach from the battery bank to the starter battery if I ever need to jump myself.

I have put a lot of weight into the van and probably more to come as I install some sort of water holding tank(It is amazing how much weight water adds). So I probably should do the shocks at some point soon. I just replaced the transmission fluid and was told at my last oil change that I should probably do the rear differential service next(seems easy enough to do myself from what I have seen). Good to hear about the timing belt, I hadn't got that far yet, but thats something I wouldn't feel too comfortable doing without a more experienced comrade to help. My last car had a timing chain, which they said should last the lifetime of the car, so it's been a while since I had to worry about that.

This thing has been a lot of work, but has kept me dry and warm, and I'd like to return the favor by keeping it running as long as I can. Thanks again!
 

Jerrell

Well-known member
Joined
Aug 27, 2017
Messages
349
Reaction score
676
Location
AZ / CA
Hey bro!

I have a brakes issue. I've been getting, shuddering for lack of a better word, when going down a steep grade. It's been pretty wet too, so maybe that is playing into it.
Brake fluid level is fine and you know how old my front brakes are (how's the uke playing coming along?). So maybe the back brakes are going? How concerned should I be about this as I start heading back toward Iowa...like should I go around mountainous areas instead of through?
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
Hey bro!

I have a brakes issue. I've been getting, shuddering for lack of a better word, when going down a steep grade. It's been pretty wet too, so maybe that is playing into it.
Brake fluid level is fine and you know how old my front brakes are (how's the uke playing coming along?). So maybe the back brakes are going? How concerned should I be about this as I start heading back toward Iowa...like should I go around mountainous areas instead of through?

Howdy dude! Does the wheel shake back and forth when you brake, or just shudder/pulse? If you're riding the brakes on grades, it's going to warp the rotors, but your front ones are new, doesn't mean a few good decents won't warp a new set though. If your wheel doesn't shake bad, it's probably the rear rotors starting to warp. It helps save your brakes if you apply and release them while descenting, gives them time to cool off. Uke is great! Hope your travels are going good otherwise!
 

Jerrell

Well-known member
Joined
Aug 27, 2017
Messages
349
Reaction score
676
Location
AZ / CA
Just the shuddering thing, no motion in the wheel. I try to do the pump thing vs riding them. The shuddering isn't every time/all the time, so I'll just be more mindful and use 3 or L when I can more often as well. This trans is starting to get rough just parking on hills, so I am leary about shifting too much. haha I hate automatics!
The journey has been great...made it to the PNW/Olympic Natl Forest as planned, so now I'm just killing time til it warms up enough to head to IA.
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
Just the shuddering thing, no motion in the wheel. I try to do the pump thing vs riding them. The shuddering isn't every time/all the time, so I'll just be more mindful and use 3 or L when I can more often as well. This trans is starting to get rough just parking on hills, so I am leary about shifting too much. haha I hate automatics!
The journey has been great...made it to the PNW/Olympic Natl Forest as planned, so now I'm just killing time til it warms up enough to head to IA.

Right on I hear you. Sounds like it's probably the rear rotors then. Just try to baby it till you get out of the hills. Use your 2-3 gear on the descents, yes. Check trans oil level make sure it's in operating range. (Check while it's running, the dip stick says procedure and oil type) The mountains are brutal on cars, I'll never buy a car from the mountains!

Olympic forest Would be sweet I'll make it up there someday! I'm all the way up in the UP of Michigan now and there still over a foot of snow!!
 
  • Like
Reactions: Jerrell

Joe Btfsplk

Well-known member
Joined
Mar 16, 2009
Messages
108
Reaction score
147
Location
MKE
"I'm all the way up in the UP of Michigan now and there still over a foot of snow!!"

I used to drive truckloads of U.S. Mail from Milwaukee to the Upper Peninsula, the Iron Mountain MI post office, pick up their outbound mail, and stopped in Green Bay WI for a load of religious magazines on the way back.

Michigan is now gearing up for medical and rec marijuana; legalized in the state. This will be a boon for us landlocked upper Midwestern stoners. Things are currently being hammered out; it's only a matter of time until said and done. Let's see if Michigan can rival the western states in high-octane smoke.

It would be fun to meet with you, SaltyCrew, if you live up there. Lovely warm weather clime, brutal come winter.
 

ByronMc

Well-known member
Joined
Jul 22, 2012
Messages
425
Reaction score
275
Location
Richmond
Website
www.facebook.com
When you do go solar have a look into used tesla batteries. My uncles off grid cabin even runs an a/c at night (6000 btu, 410 watt) off if his 3 battery pack 13kwh storage setup. I believe he runs 4kw of panels though, its his whole roof plus a clearing next to the house with 12 panels (250w i believe).
At the moment, am only getting it ready to get DMV to transfer title status to RV.
Then I’ll go through the mechanical & then onto solar
 

Seethru2

New member
Joined
Feb 24, 2017
Messages
2
Reaction score
1
I just added oil and coolant recently, after an overheat, still getting close to overheating whenever I go to move. When we overheated, I put water straight into the radiator, and 3 quarts of oil. Since then I added coolant (undiluted) thinking that it would be dilute itself in the system because I had filled the system with only water to get me thru. Could this be why I'm now getting close to overheating? What should I do? Drain some coolant? Add some water?
 

Hylyx

Well-known member
Joined
Apr 5, 2012
Messages
234
Reaction score
479
If you already overheated you may have killed the thermostat(an easy fix).what vehicle do you have? Usually you'll wait till it's cold, fill up the radiator until it's full, close the radiator, run the engine for like a minute, fill the radiator again, and then fill the reservoir while the engine runs.

And yeah, if you know your mixture isn't right, adding just coolant won't hurt anything, it will definitely mix up in the engine.
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
If you already overheated you may have killed the thermostat(an easy fix).what vehicle do you have? Usually you'll wait till it's cold, fill up the radiator until it's full, close the radiator, run the engine for like a minute, fill the radiator again, and then fill the reservoir while the engine runs.

And yeah, if you know your mixture isn't right, adding just coolant won't hurt anything, it will definitely mix up in the engine.

This advice is maybe 1/3 true. Yes if a thermostat sticks closed, it will overheat the engine. You feel the upper radiator hose, even squeeze it to see if there is coolant coming through. If upper hose is cold while engine is hot, thermostat is stuck shut.
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
I just added oil and coolant recently, after an overheat, still getting close to overheating whenever I go to move. When we overheated, I put water straight into the radiator, and 3 quarts of oil. Since then I added coolant (undiluted) thinking that it would be dilute itself in the system because I had filled the system with only water to get me thru. Could this be why I'm now getting close to overheating? What should I do? Drain some coolant? Add some water?

How long did you let it stay running when it over heated? If you added coolant, it's losing it somewhere. Fill it up, run it, see where it's coming out. If it's not leaking, it's burning it internally, that's bad. That means you popped a head gasket.

Did you check the level of the oil before you added 3 quarts? That's alot of oil to add, as most engines only take 4-6 quarts total. If you added 3 quarts oil for fun and didn't check it, you'll fuck it up.

Stuck thermostat can cause overheat. Broken radiator fan can cause overheat. Low coolant level can cause overheat. Bad radiator cap can cause overheat. Any leak in the cooling system can cause over heat.
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
If you drove it any distance while the temp was pegged, chances are you made it worse. It over heated for a reason, and until that is fixed it will keep overheating. If it was simply low on coolant, and you filled it up, shouldn't overheat anymore. The fact it still overheats, something is broken, one of things I suggested in previous post. Good luck, overheated engines tend to need major repair (head gasket). If you shut it down before it started bubbling and smoking everywhere, might be able to save it. Have a pro look at it, shouldn't take long to figure out what's wrong.
 
  • Like
Reactions: Seethru2

marmar

Well-known member
Joined
Apr 19, 2016
Messages
210
Reaction score
225
Location
New mexico
Website
soundcloud.com
Ahh i see. Did the blower fan work normally before you had replaced the battery, and wired it incorrectly?

Try getting to the electrical plug in back of switch and unplug it. See if that shuts off blower.
Hey again, so I unplugged that thing and now I noticed it's still blowing hot air while the car is in drive. Doesn't blow when in park and on. Weird huh? Could that be connected to thermostat, no? I still haven't checked all the wires . ..
Now there is another issue , under the truck , they refused to do tire rotation on it and gave me the whole list of what needs to be done before, like a grand of money. Could you please take a look at this list and point which really needs immediate attention and what can wait? Also how real is it to do myself? Thanks 😘
 

Attachments

  • IMG_20190424_200502802.jpg
    IMG_20190424_200502802.jpg
    854.3 KB · Views: 268

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
Hey again, so I unplugged that thing and now I noticed it's still blowing hot air while the car is in drive. Doesn't blow when in park and on. Weird huh? Could that be connected to thermostat, no? I still haven't checked all the wires . ..
Now there is another issue , under the truck , they refused to do tire rotation on it and gave me the whole list of what needs to be done before, like a grand of money. Could you please take a look at this list and point which really needs immediate attention and what can wait? Also how real is it to do myself? Thanks 😘

Blower motor is not wired to thermostat, no. Sounds like it's been auxillary wired. Air will naturally come through vents while driving if it's set to fresh. Try moving to the "recirculate" position to close the fresh air vent, this will keep the hot engine air out out of the cabin.

As for the suggested repairs by the shop, they do not want to break anything while doing a tire rotation, so they quoted you to fix it. They are saving their own ass by telling you your truck is is poor condition and they don't want to touch it unless you want to fix the problems. All that stuff can be replaced with basic hand tools, yes. Do the tire rotation yourself, that's basic stuff.
 
  • Useful
Reactions: marmar

Jerrell

Well-known member
Joined
Aug 27, 2017
Messages
349
Reaction score
676
Location
AZ / CA
How about tire sizes. I have 215/65/R16's and need two tires. I can get two 215/60/R16's for $30...if I rotate tires so I have matching sizes up front and matching in back, will that screw things up?
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
How about tire sizes. I have 215/65/R16's and need two tires. I can get two 215/60/R16's for $30...if I rotate tires so I have matching sizes up front and matching in back, will that screw things up?

Hey man! You should be fine as long as you keep the same tire sizes on front and same size on back. If you had an AWD vehicle, yes it would potentially cause damage, but if you're still rocking your van, it's only FWD so you'll be fine. Just don't mix and match on one end or the other.
 
  • Useful
Reactions: Jerrell

WyldLyfe

I'm a d-bag and got banned.
Banned
Joined
Jun 3, 2019
Messages
228
Reaction score
303
Location
tasmania
Bro what's it mean when a automobiles got the air bag sign on, on the dash, an the horn ain't beepin. It beeps when only in park when the sign goes off, Thx.
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
Bro what's it mean when a automobiles got the air bag sign on, on the dash, an the horn ain't beepin. It beeps when only in park when the sign goes off, Thx.

Howdy! Air bag light can mean a whole lot of things, but in your case, since you gave me the info of horn also not working, it's most deff 99% sure it's your "clock spring" or "sprial cable" that's gone bad. It's located inside the steering wheel behind the air bag. Fairly easy to replace. Make sure to disconnect the battery before you start messing with the air bag system. The whole "squib" will unbolt from the steering wheel, usually 2 bolts behind the 4 and 8 o'clock positions of the wheel. There will be 2 wires connecting the air bag squib to the "clock spring" and steering wheel.

Basically, the thing that went bad on you, allows the steering wheel to rotate while keeping a constant connection to the air bag. Same goes for the horn. The wires for the horn and airbag run through the clock spring.

Unfortunately, they are usually a fairly expensive part to replace. Good luck! If you have any more questions, feel free!
 

BradKajukenbo

Well-known member
Joined
Jun 5, 2019
Messages
207
Reaction score
559
Location
Dunsmuir Califonia
I have no clue what goes on under the hood. I am the type of person who has left over pieces when I try to fix things.

I have a 99 Expedition. About 2 months ago, all of the sudden the turn signals and break lights just stopped working. So I googled it. I ended up replacing the little square flasher things under the dashboard. That wasn't it. I replace fuse #13 which is for the break lights. As soon as I turn the key on, the fues goes "Pop".

What I did find out, the person who sold it to me, before selling it, he removed his Kenwood system by cutting all the wires and shoving them back into the dashboard then slid the stock radio in. I capped all ends of the wires. Now sometimes I have turn signals and if I want break lights, I have to start the fucker then put the fuse into slot #13.
 

SaltyCrew

∆-FLY LOW-∆
Joined
Sep 21, 2018
Messages
120
Reaction score
316
Location
Midwest
I have no clue what goes on under the hood. I am the type of person who has left over pieces when I try to fix things.

I have a 99 Expedition. About 2 months ago, all of the sudden the turn signals and break lights just stopped working. So I googled it. I ended up replacing the little square flasher things under the dashboard. That wasn't it. I replace fuse #13 which is for the break lights. As soon as I turn the key on, the fues goes "Pop".

What I did find out, the person who sold it to me, before selling it, he removed his Kenwood system by cutting all the wires and shoving them back into the dashboard then slid the stock radio in. I capped all ends of the wires. Now sometimes I have turn signals and if I want break lights, I have to start the fucker then put the fuse into slot #13.

Do you have a question, or just telling a story?
 

About us

  • Squat the Planet is the world's largest social network for misfit travelers. Join our community of do-it-yourself nomads and learn how to explore the world by any means necessary.

    More Info

Help us pay the bills!

Total amount
$10.00
Goal
$100.00

Latest Library Uploads